ニュース

ニュース

  • Company introduction

    Hebei Liyong Flowtech Co., Ltd. is a leading manufacturer and exporter of valves, fittings, flanges, pipes and other piping products. Our company is located in the North China Plain of China, which is rich in resources and rich in industrial heritage. We specialize in the manufacture of a wide ra...
    続きを読む
  • バルブ

    A valve is a device or natural object that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an...
    続きを読む
  • バルブの鋳造材料

    Casting Materials of Valves ASTM Casting Materials Material ASTM Casting SPEC Service Carbon Steel ASTM A216 Grade WCB Non-corrosive applications including water, oil and gases at temperatures between -20°F (-30°C) and +800°F (+425°C) Low Temp Carbon Steel ASTM A352 Grade LCB Low temperatu...
    続きを読む
  • 新旧のDIN指定

    新旧のDIN指定何年にもわたって、多くのDIN規格がISO規格に統合され、したがってEN規格の一部にもなりました。 欧州規格の改訂の過程で、いくつかのDIN規格が撤回され、DIN ISOENおよびDINENに置き換えられました。 使用される標準...
    続きを読む
  • バルブアクチュエータの紹介

    バルブ アクチュエータの概要 バルブ アクチュエータ バルブ アクチュエータは、バルブの操作に必要なトルクや自動作動の必要性など、さまざまな要因に基づいて選択されます。 アクチュエータのタイプには、手動ハンドホイール、手動レバー、電気モーター、空圧式、ソレノイド、油圧式などがあります...
    続きを読む
  • バルブ、継手、フランジの一般的なマーキング基準と要件

    Generic Marking Standards and Requirements Component Identification The ASME B31.3 Code requires random examination of materials and components to ensure conformance to listed specifications and standards. B31.3 also requires these materials to be free from defects. Component standards and spec...
    続きを読む
  • フランジのトルク締め

    Torque Tightening To obtain a leak-free flange connection, a proper gasket installation is needed, the bolts must be assign on the correct bolt tension, and the total bolt strength must be evenly divided over the whole flange face. With Torque Tightening (the application of preload to a fasten...
    続きを読む
  • フランジ ガスケット & ボルト

    Flanges Gaskets & Bolts Gaskets To realize a leak-free flange connection gaskets are necessary. Gaskets are compressible sheets or rings used to make a fluid-resistant seal between two surfaces. Gaskets are built to operate under extreme temperature and pressures and are available in a wide ...
    続きを読む
  • フランジ面仕上げ

    Flange Face Finish Flange face finish The ASME B16.5 code requires that the flange face (raised face and flat face) has a specific roughness to ensure that this surface be compatible with the gasket and provide a high quality seal. A serrated finish, either concentric or spiral, is required wi...
    続きを読む
  • フランジ面

    Flange Faces What is a Flange face? Different types of flange faces are used as the contact surfaces to seat the sealing gasket material. ASME B16.5 and B16.47 define various types of flange facings, including the raised face, the large male and female facings which have identical dimensions to...
    続きを読む
  • フランジの種類

    Types of Flanges Flange types As already described before, the most used flange types ASME B16.5 are: Welding Neck, Slip On, Socket Weld, Lap Joint, Threaded and Blind flange. Below you will find a short description and definition of each type, completed with an detailed image. Most common flang...
    続きを読む
  • フランジの圧力クラス

    Pressure Classes of Flanges Forged steel flanges ASME B16.5 are made in seven primary Pressure Classes: 150 300 400 600 900 1500 2500 The concept of flange ratings likes clearly. A Class 300 flange can handle more pressure than a Class 150 flange, because a Class 300 flange are co...
    続きを読む
123次> >> ページ 1 / 3