Notícia

Notícias

  • Company introduction

    Hebei Liyong Flowtech Co., Ltd. is a leading manufacturer and exporter of valves, fittings, flanges, pipes and other piping products. Our company is located in the North China Plain of China, which is rich in resources and rich in industrial heritage. We specialize in the manufacture of a wide ra...
    Consulte Mais informação
  • válvulas

    A valve is a device or natural object that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an...
    Consulte Mais informação
  • Materiais de Fundição de Válvulas

    Casting Materials of Valves ASTM Casting Materials Material ASTM Casting SPEC Service Carbon Steel ASTM A216 Grade WCB Non-corrosive applications including water, oil and gases at temperatures between -20°F (-30°C) and +800°F (+425°C) Low Temp Carbon Steel ASTM A352 Grade LCB Low temperatu...
    Consulte Mais informação
  • Designações DIN antigas e novas

    Velhas e novas designações DIN Com o passar dos anos, muitos padrões DIN foram integrados aos padrões ISO e, portanto, também fazem parte dos padrões EN. No curso da revisão dos padrões europeus, os padrões serveral DIN foram retirados e substituídos por DIN ISO EN e DIN EN. Os padrões usados ​​...
    Consulte Mais informação
  • Introdução aos atuadores de válvula

    Introdução aos atuadores de válvula Atuadores de válvula Os atuadores de válvula são selecionados com base em vários fatores, incluindo o torque necessário para operar a válvula e a necessidade de atuação automática. Os tipos de atuadores incluem volante manual, alavanca manual, motor elétrico, pneumático, solenóide, hidra...
    Consulte Mais informação
  • Padrões e requisitos genéricos de marcação para válvulas, conexões, flanges

    Generic Marking Standards and Requirements Component Identification The ASME B31.3 Code requires random examination of materials and components to ensure conformance to listed specifications and standards. B31.3 also requires these materials to be free from defects. Component standards and spec...
    Consulte Mais informação
  • Torque de aperto para flange

    Torque Tightening To obtain a leak-free flange connection, a proper gasket installation is needed, the bolts must be assign on the correct bolt tension, and the total bolt strength must be evenly divided over the whole flange face. With Torque Tightening (the application of preload to a fasten...
    Consulte Mais informação
  • Juntas e parafusos de flange

    Flanges Gaskets & Bolts Gaskets To realize a leak-free flange connection gaskets are necessary. Gaskets are compressible sheets or rings used to make a fluid-resistant seal between two surfaces. Gaskets are built to operate under extreme temperature and pressures and are available in a wide ...
    Consulte Mais informação
  • Acabamento da Face do Flange

    Flange Face Finish Flange face finish The ASME B16.5 code requires that the flange face (raised face and flat face) has a specific roughness to ensure that this surface be compatible with the gasket and provide a high quality seal. A serrated finish, either concentric or spiral, is required wi...
    Consulte Mais informação
  • Faces de Flange

    Flange Faces What is a Flange face? Different types of flange faces are used as the contact surfaces to seat the sealing gasket material. ASME B16.5 and B16.47 define various types of flange facings, including the raised face, the large male and female facings which have identical dimensions to...
    Consulte Mais informação
  • Tipos de Flanges

    Types of Flanges Flange types As already described before, the most used flange types ASME B16.5 are: Welding Neck, Slip On, Socket Weld, Lap Joint, Threaded and Blind flange. Below you will find a short description and definition of each type, completed with an detailed image. Most common flang...
    Consulte Mais informação
  • Classes de pressão de flanges

    Pressure Classes of Flanges Forged steel flanges ASME B16.5 are made in seven primary Pressure Classes: 150 300 400 600 900 1500 2500 The concept of flange ratings likes clearly. A Class 300 flange can handle more pressure than a Class 150 flange, because a Class 300 flange are co...
    Consulte Mais informação
123Next> >> Página 1 / 3